Industrial Multifunction VPN Router w/up to 2x WiFi 11ac + up to 2 LTE 4G + 2 serial ports + 6 Gigabit Ethernet Switch w/ Load Balancing, VPN, Protocol Gateway, Storage**; 24V/HV input
- Up to 2 concurrent WIFI 11ac and redundancy (1L-2AC model)
- Up to 2 concurrent mobility for 3G/4G LTE Link & GPS (2L-1AC model/4 SIMs)
- Support LTE Cat 6 (APAC & EUNA models) or Cat 12/9/13 (WW model)
- Built-in 6 Gigabit Ethernet switch
- Dual radio for 802.11ac/a/b/g/n with concurrent 5GHz & 5GHz bands up to 2.6Gbps Wi-Fi bandwidth(to 2AC model)
- WIFI radio for 802.11ac/a/b/g/n with 5GHz or 2.4GHz
- Support WIFI 802.11e traffic prioritization and WMM
- MIMO technology 3T3R up 6 antenna(2AC); SMA type external antenna
- Support Client-base roaming
- Supports AP/ Bridge/ Client/ MESH modes
- Support 802.11s Wireless Mesh Network
- Advanced wireless security WEP64/128bits/ WPA/ WPA-PSK (TKIP,AES)/ WPA2/ WPA2-PSK (TKIP,AES)
- VPN router for Multi-site VPN, OpenVPN, L2TP over IPsec, IPsec, L2 over GRE , IPGRE
- Load Balancing built-in 5 mechanisms
- Optional EMMC Flash storage on-board**
- Optional eSIM chip enables router with versatile data plans**
- Support NAT and Firewall
- Support Modbus gateway on serial ports
- Support 2 RS422/RS485 ports with 2.5KV isolation or 2x RS232 ports
- Input voltage for 24V model
- Environmental monitoring for router inside info with voltage, current, temperature; Wi-Fi & LTE graphic signal strength
- Editable login page of captive portal for hot-spot application
- USB port to backup, restore the configuration file and upgrade firmware; Dual image firmware
- ITxPT compliant w/ ignition function**
Lantech IWMR-3006 series is a next generation industrial multi-function VPN router w/up to 2x 802.11ac Wi-Fi + up to 2x LTE modem + 6x Gigabit Ethernet switch + 2 serial ports that supports advanced function of VPN, Load-balancing, Protocol gateway(Modbus), EMMC Flash Storage**, WiFi roaming and LTE quad SIM fail-over for industrial applications. The dual core CPU with 1.6GHz + 256M flash enables the router to multi-task smoothly.
Support AP/Bridge/Client mode, Mesh roaming
IWMR-3006 supports AP/Bridge/Client mode for different applications.
It also supports client-base roaming to swap between the APs in a network.
Built-in Wireless mesh network（WMN）
IWMR-3006 supports mesh network composed of different nodes. The set of SSIDs allow the wireless client to roam freely without the need for complicated account management. With Mesh protocol, it can provide a reliable, scalable, stable and seamless network topology.
Dual concurrent LTE design 4G/3G for load-balancing
With dual LTE module design (2L model), 4 SIM card slots, IWMR-3006 can allow auto-swap, failover & failback between multiple service providers for real non-stop connection. With concurrent LTE modules, it can also allocate bandwidth by “ Load Balancing with 8 schemes between multiple WANs.
With one mobile LTE module (1L model), 2 SIM card slots, IWMR-3006 provides redundant link between two service providers.
Both GPS and Russian GLONASS systems are supported.
IEEE 802.11ac dual band radio up to 2.6Gbps bandwidth
With IEEE 802.11ac capability, IWMR-3006 can operate either 5GHz or 2.4GHz bands, offering the maximum speed of 2.6Gbps bandwidth (1.3Gbps per 1AC). It is also compatible with 802.11g/n that can work with 2.4GHz for longer range transmission.
The Wi-Fi 11ac supports AP/BRIDGE/AP Client modes can be diverse for most of wireless application. Working with Load-balancing “Priority” mode, the AP client can enable router to transmit on Wi-Fi with first priority.
MIMO technology with 3T3R and SMA type connectors
Lantech IWMR-3006 series adapts MIMO technology with smart antenna transmission and reception for 3T3R. With six external detachable omni connectors and optional antennas, IWMR-3006 can have better Wi-Fi & LTE/GPS coverage.
Wireless WMM QoS
IWMR-3006 supports 802.11e standard which defines a set of Quality of Service for wireless LAN applications as well as WMM (WIFI multimedia)
Advanced security & 16 SSIDs
The security support standards including 64/128bits WEP, WPA/WPA2 PSK (TKIP, AES), 802.1x ensures the best security and active defense against security treads. Lantech IWMR-3006 support up to 16 SSIDs, each SSID has its independent security and encryption.
Load Balancing with 5 mechanisms for multi-WANs
IWMR-3006 supports Load Balancing for LTE/WAN connections. There are five schemes for Load Balancing function:
|Basic||Fixed||Manually route by traffic type through fixed WAN link.|
|Failover||Routes connections through preferred WAN link while others stand-by. Sequentially activate another link if preferred link fail occurs. Once failover will not failback until link loss.|
|Priority||Routes connections through preferred WAN link as primary while others follow by. Ex. Wi-Fi client>LTE>others|
|Weighted Round-Robin||Evenly distribute the traffic over all working WAN links in circular order according to the specified weights.|
|Custom Route||Routing through the selected WAN for each specific traffic, ex: TCP/UDP port number and IP address.|
2 port serial connection, Modbus gateway
It builds in 2 port serial connection for RS232, RS422, RS485 in which RS422/RS485 has 2.5KV isolation protection.
The built-in Modbus gateway can convert Modbus RTU/ASCII to Modbus TCP for device control.
Optional EMMC Flash storage**
The optional EMMC flash storage on router can offer 8G/16G/32G capacity.
By replacing physical SIM, optional eSIM chip will allow users to purchase data plans at low prices from local carriers in the world.
VPN and firewall
Besides traditional VPN peer to peer tunneling, IWMR-3006 support latest Multi-Site VPN function that is an efficient way for mesh tunneling. The registration is under cloud service and encrypted by SSH makes the connection easy and safe.
It supports Multi-Site VPN, OpenVPN, L2TP over IPsec, IPsec, L2 over GRE , IPGRE, and NAT for various VPN applications.
The built-in Layer-4 firewall includes DDoS, IP address filter / Mac address filter / TCP/UDP port number.
DIDO for alarm & email notice; Event log; Remote Web control
2 sets of DIDO functions can support additional high/low physical contact for designate applications besides Port / Power events, for example, DIDO function can trigger alarm if the router was moved or stolen. In case of events, the IWMR-3006 will immediately send email and trap.
When the router is at remote area with limited access, Web control can help to get router status or remotely reboot.
24V/HV isolated input voltage selection: dual 9V-56VDC (24V model) or single 90~305VAC/120~430VDC (HV model)
The IWMR-3006 is able to work from 9VDC to 56VDC (24V model) Or with single high power supply at 90~305VAC / 120~430VDC (HV model).
Environmental monitoring for inside router info& alerting; Graphic WIFI & LTE signal strength
The built-in environmental monitoring can detect router ambient temperature, voltage, current where can send the syslog and email when abnormal.
The graphic WIFI & LTE signal strength shows connection status at a glance.
USB port for back up, restore configuration and upgrade firmware; Dual image firmware
The built-in USB port can upload/download the firmware through USB dongle for router replacement
It support dual-image firmware to choose which one to start.
Dual image firmware
It supports dual-image firmware to choose which one to start.
Editable login page of captive portal
The IWMR-3006 supports editable captive portal function that allows administrator to force end-users redirect to authentication page.
Ruggedized industrial design and FCC, CE & E-marking** certificate
The IWMR-3006 is designed to meet with industrial network environment with IP 30 housing. It passed tests under extensive Industrial EMI and environmental vibration and shocks standards.
With CE & FCC radio certification for WIFI and LTE and E-marking** certificate, the IWMR-3006 is best for outdoor community, vehicle, process control automation etc. For more usage flexibilities, IWMR-3006 supports wide operating temperature from -40°C to 65°C.
Ignition sense allows you to delay power off your Ethernet switch with a designated time delay.
Built-in Managed Switch Function
Managed switch function is built-in and provides various L2+ functions for network aggregation deployment. It delivers ports and PoE management, VLAN, QoS, multicast, redundant ring, and security functions.