SFP+ 10Gbps Copper (30M)

10G Copper SFP+ Transceiver, 30M

Distance: 30M
Standard Operating Temperature: 0°C ~ 70°C
1G/ 2.5G/ 5G/ 10GBase-T Application

OVERVIEW

Lantech SFP-10GB-T Small Form Factor Pluggable SFP+ Copper transceivers are compliant with the current SFP+ Multi-Source Agreement (MSA) Specification. The high performance designed is integrated full duplex data link at 10Gbps over four pair Category 6a/7 cable up to 30m links. It is specifically designed for high speed communication links that require 10 Gigabit Ethernet over copper cable.

FEATURES

Compliant with IEEE 802.3az, 802.3ab and 802.3 standard
Compliant with SFP+ MSA (SFF-8431, SFF-8432)
Support 10GBase-T/ 5GBase-T/ 2.5GBase-T/ 1000Base-T
Hot Pluggable
Auto-negotiates with other 10GBase-T PHYs
Auto-detect MDI/MDI-X
Support RX_LOS function
I2C 2-wire interface for serial ID and PHY register access
RJ-45 connector
Single +3.3V power supply
10G link length up to 30m with Cat.6a/7, 2.5G/5G link length up to 50m with Cat.5E, 1G link length up to 100m with Cat.5E
RoHS Compliant

SPECIFICATIONS

Absolute Maximum Ratings

Parameter	Symbol	Min.	Max.	Unit	Note
Storage Temperature	TsT	-40	+85	°C
Supply Voltage	VccT, VccR	-0.5	+4.0	V
Storage Relative Humidity	RH	5	95	%

Recommended Operating Conditions

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Case Operating Temperature	ToP	0	–	+70	°C
Supply Voltage	Vcc	+3.13	+3.3	+3.47	V
Supply Current	Icc			880	mA
Power Consumption @30M	PCW			2.9	W

General Specifications

Vcc= 3.15V to 3.46V, Top = 0 C to 70 C

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Data Rate	DR	1	10.3125		GB/sec
Bit Error Rate	BER			10-12

High-Speed Electrical Interface, Host to SFP+

Vcc= 3.13V to 3.47V, Top = 0 C to 70 C

Parameters	Symbol	Min.	Typ.	Max.	Unit	Note
TD+, TD- Input Voltage Swing	VIN+ / VIN-	250		1200	mV	1
RD+, RD- Output Voltage Swing	Vout+ / Vout-	350		800	mV	1
Rise Time (Receiver)	Tr		175		ps	2
Fall Time (Receiver)	Tf		175		ps	2
Tx Input Impedeance	Zin		50		Ohm	1
Rx Output Impedeance	Zout		50		Ohm	1
Note1: Single ended Note2: 20% to 80% value

High-Speed Electrical Interface, Cable to SFP+

Vcc= 3.13V to 3.47V, Top = 0 C to 70 C

Parameters	Symbol	Min.	Typ.	Max.	Unit	Note
TX Output Impedance	Zout.TX		100		Ohm	1
RX Output Impedance	Zin.RX		100		Ohm	1
Note1: Differential for frequencies ranging from 125MHz to 10.3125GHz

Pin Assignment

Pin Description

Pin	Name	Function / Description
1	VeeT	Transmitter Ground
2	TX_Fault	Transmitter Fault Indication (1)
3	TX_Disable	Transmitter Disable – Turns off transmitter laser output (2)
4	SDA	2-wire Serial Interface Data Line (SDA: Serial Data Signal) (3)
5	SCL	2-wire Serial Interface Clock (SCL: Serial Clock Signal) (3)
6	Mod_ABS	Module Absent, connected to VeeT or VeeR in the module (3)
7	RS0	Rate Select 0, optionally controls SFP+ module receiver (5)
8	Rx_LOS	Receiver Loss of Signal Indication (4)
9	RS1	Rate Select 1, optionally controls SFP+ module transmitter (5)
10	VeeR	Receiver Ground
11	VeeR	Receiver Ground
12	RD-	Receiver Inverted Data output, Differential LVPECL, AC coupled
13	RD+	Receiver Non-Inverted Data output, Differential LVPECL, AC coupled
14	VeeR	Receiver Ground
15	VccR	Receiver 3.3V Power Supply
16	VccT	Transmitter 3.3V Power Supply
17	VeeT	Transmitter Ground
18	TD+	Transmitter Non-Inverted Data Input, Differential LVPECL, AC coupled
19	TD-	Transmitter Inverted Data Input, Differential LVPECL, AC coupled
20	VeeT	Transmitter Ground
Note1: TX Fault is not used and is always tied to ground through a 100 ohm resistor. Note2: TX Disable as described in the MSA is not applicable to the Copper-T module, but is used for convenience as an input to reset the internal PHY IC. This pin is pulled up within the module with a 4.7KΩ resistor. Low (0 – 0.8 V): Transceiver on ; Between (0.8 V and 2.0 V): Undefined High (2.0 – 3.465 V): Transceiver in reset state Open: Transceiver in reset state Note3: These are the module definition pins. They should be pulled up with a 4.7K~10KΩ resistor on the host board to supply less than VccT+0.3V or VccR+0.3V. Mod-ABS is grounded by the module to indicate that the module is present. Note4: LVTTL compatible with a maximum voltage of 2.5V. Note5: No connect on this module.

ORDER INFORMATION

Part Number	Speed mode	Link	Temp.
8330-206	10GBase-T @Cat.6a/7 cable	30 meters	0~70°C
	5GBase-T/2.5GBase-T @Cat.5E cable	50 meters
	1000Base-T @Cat.5E cable	100 meters