EN50155 Multifunction VPN Router w/1x WiFi 11ac + 1 LTE 4G + 2 serial ports + 4 Gigabit X-coded PoE Switch + 2 WAN/LAN w/Load Balancing**, TWCC**, VPN, Protocol Gateway, Storage**;WV input

  • Built-in 4 Gigabit X-coded PoE Ethernet managed switch +2 WAN/LAN ports
  • WIFI radio for 802.11ac/a/b/g/n with 5GHz or 2.4GHz
  • Support WIFI 802.11e traffic prioritization and WMM
  • MIMO technology 3T3R up to 6 antenna; Detachable antenna connectors with 6 SMA/QMA** type incl. 3 WIFI + 3 LTE
  • Fast roaming **, 802.11r work with Lantech controller
  • Supports AP/ BRIDGE/Client modes
  • Advanced wireless security WEP64/128bits/ WPA/ WPA-PSK (TKIP*,AES)/ WPA2/ WPA2-PSK (TKIP*,AES)
  • Optional TWCC** (Train Wireless Carriage Coupling)for auto wireless coupling
  • VPN router for Multi-site VPN, OpenVPN, L2TP, IPsec, PPTP**, L2 over GRE
  • Load Balancing** support 8 mechanism
  • Optional EMMC Flash storage on-board**
  • Support NAT and Firewall
  • Support Modbus gateway on serial ports
  • Support 2 RS422/485 ports with 2.5KV isolation or 2x RS232 ports
  • Optional 2 GT smart bypass protection
  • Galvanic isolation on WV model from 16.8V~137.5V input with PoE budget 60W
  • Environmental monitoring for router inside info with voltage, current, temperature and total PoE load;; WIFI & LTE graphic signal strength & TX/RX rate display
  • Editable login page of captive portal for hot-spot application
  • USB port to backup, restore the configuration file and upgrade firmware*; Dual image firmware*


Lantech TPWMR-5004 series is a next generation EN50155 multi-function VPN router w/ 1 x 802.3ac Wi-Fi + 1 x LTE modem +4 Gigabit X-coded PoE Ethernet switch + 2 WAN/LAN ports + 2 serial ports that supports advanced function of VPN, Load-balancing**(Premium pack), EMMC Flash Storage**, TWCC**, Protocol gateway(Modbus*), Storage**, Wi-Fi roaming** and LTE dual SIM fail-over for industrial applications. The dual core CPU with 1.6GHz + 256M flash enables the router to multi-task smoothly.

Optional TWCC** (Train Wireless Carriage Coupling) for auto coupling
TPWMR-5004 supports series supports optional TWCC** (Train Wireless Carriage Coupling) that enables auto wireless coupling to reconnect APs.

LTE design 4G/3G w/2SIMs for redundancy
With one mobile LTE module (1L model), 2 SIM card slots, TPWMR-5004 provides redundant link between two service providers. Both GPS and Russian GLONASS systems are supported.

Optional EMMC Flash storage**
The optional EMMC flash storage on router can offer 8G/16G/32G capacity.

IEEE 802.11ac one band radio up to 1.3GMbps bandwidth
With IEEE 802.11ac capability, TPWMR-5004 can operate either 5GHz or 2.4GHz bands, offering the maximum speed of 1.3GMbps bandwidth it is also compatible with 802.11g/n that can work with 2.4GHz for longer range transmission.

MIMO technology with 3T3R and standard SMA / optional QMA type connectors
Lantech TPWMR-5004 series adapts MIMO technology with smart antenna transmission and reception for 3T3R. With six external detachable antenna SMA/QMA** connectors and optional antennas, TPWMR-5004 can have better Wi-Fi & LTE/GPS coverage.

Optional 802.11r fast roaming**
TPWMR-5004 support fast roaming** in coordination with Lantech Wireless Controller to allow encryption keys to be stored on all of the APs in a network. Client mode supports PMK** Caching and pre-authentication.

Wireless WMM QoS
TPWMR-5004 supports 802.11e standard which defines a set of Quality of Service for wireless LAN applications as well as WMM (WIFI multimedia)

Advanced security & 16 SSIDs
The security support standards including 64/128bits WEP, WPA/WPA2 PSK (TKIP*, AES), 802.1x** ensures the best security and active defense against security treads. Lantech TPWMR-5004 support up to 16 SSIDs, each SSID has its independent security and encryption.

Load Balancing** with 8 mechanism for multi-WANs (premium license)
TPWMR-5004 supports Load Balancing** for LTE/WAN connections. There are eight schemes for Load Balancing** function:

Pack Algorithm Description
Standard Fixed Manually route by traffic type through fixed WAN link.
Basic Package Failover Routes connections through preferred WAN link while others stand-by. Sequentially activate another link if preferred link fail occurs. Once failover will not failback until link loss.
Priority Routes connections through preferred WAN link as primary while others follow by. Ex. Wi-Fi  client>LTE>others
Weighted Round-Robin Evenly distribute the traffic over all working WAN links in circular order according to the specified weights.
Custom Route Routing through the selected WAN for each specific traffic, ex: TCP/UDP port number and IP address.
Full Package (incl. basic package) Sticky Session* Binding all connections in an application session to particular WAN link to ensure all connections in the session are routed to the same WAN link , that is suitable for security services like online payment etc.
Smallest Load* Routes connections through the WAN link with highest free bandwidth ratio.
The ratio = 1 – (traffic load / the capability of a WAN link).
The traffic load could be defined by downstream, upstream or total traffic
Fastest* Routes connections through the WAN link with lowest latency time.

2 port serial connection, Modbus gateway
It builds in 2 port serial connection for RS232; RS422/ 485 in which RS422/485 has 2.5KV isolation protection. The built-in Modbus gateway can convert Modbus RTU/ASCII to Modbus TCP for device control.

Support various VPN applications and firewall
Besides traditional VPN peer to peer tunneling, TPWMR-5004 support latest Multi-Site VPN function that is an efficient way for mesh tunneling. The registration is under cloud service and encrypted by SSH makes the connection easy and safe. It supports Multi-Site VPN, Open VPN, L2TP, IPsec L2 over GRE, NAT, and PPTP** for various VPN applications. The built-in Layer-4 firewall includes DoS**, IP address filter / Mac address filter* / TCP/UDP port number.

DIDO for alarm & email** notice; Event log; Remote Web/SMS** control
2 sets of DIDO function can support additional high/low physical contact for designate applications besides Port / Power events, for example, DIDO function can trigger alarm if the router was moved or stolen. In case of events, the TPWMR-5004 will immediately send email** and trap. The event log can be sent via syslog, emails or trigger the alarm relay. When the router is at remote area with limited access, Web/SMS** control can help to get router status or remotely reboot by Web/SMS**.

Wide range input voltage from 16.8~137.5VDC (WV model); Built-in 4 port PoE at/af switch with 60W budget
The TPWMR-5004 is able to work from 16.8~137.5V (WV with isolation) for 4 port PoE at/af with PoE budget 60W that is particular good for vehicle, rail train, depot etc. application

Environmental monitoring for inside router info& alerting; Graphic WIFI & LTE signal strength and TX/RX rate display
The built-in environmental monitoring can detect router ambient temperature, voltage, current and total PoE load where can send the syslog, email** and SMS** alert when abnormal.

Built-in Managed Switch Function
Managed switch function is built-in and provides various L2+ functions for network access deployment. It delivers ports and PoE management, VLAN, QoS, multicast, redundant ring, and security functions.

Dual image firmware*
It supports dual-image firmware* to choose which one to start.

Editable login page of captive portal
The TPWMR-5004 supports editable captive portal function that allows administrator to force end-users redirect to authentication page.

USB port for back up, restore configuration and upgrade firmware*
The built-in USB port can upload/download/upgrade the firmware through USB dongle for router replacement

Ruggedized EN50155 design and FCC/CE & E-marking** certificate
The TPWMR-5004 series is verified with EN50155, EN61373, EN45545 standard with IP65/54 housing. It passed serious tests under extensive Industrial EMI and environmental vibration and shocks standards. With CE & FCC radio certification for LTE and E-marking** certificate, the TPWMR-5004 is best for outdoor community, vehicle, power substation, process control automation etc. For more usage flexibilities, TPWMR-5004 supports operating temperature from -20°C to 70°C or -40°C to 70°C(-E)

*Future Release