16 10/100TX + 4 10/100/1000T X-coded L2+ 16 PoE at/af EN50155 Managed Ethernet Switch w/ enhanced G.8032 Ring

  • EN50155/EN61373/EN45545-2 verification
  • IEEE802.3at/af up to 30W per port; PoE management incl. detection and scheduling
  • WV dual input steps down to 54V output PoE max.80W; optional 24V input can boost to 54V output PoE max 80W
  • Enhanced G.8032 ring protection < 20ms for single ring. Supports auto mode, enhanced mode, train mode, multi-VLAN and basic mode; Enhanced G.8032 ring covers
  • Multicast packets; MSTP 16MSTI /RSTP ; support MRP ring**
  • Miss-wiring avoidance & node failure protection
  • Support LACP link aggregation, IGMP v3/router port, DHCP server & DHCP Option82; Port based DHCP distribution, Mac based DHCP server, QoS by VLAN, SSH/SSL, HTTPS, INGRESS/EGRESS ACL L2/L3, TACACS+, QinQ, SMS**
  • Protocol based VLAN** ; IPv4/IPv6 Subnet based VLAN**
  • Environmental Monitoring for temp., voltage, current and total PoE load
  • Optional bypass in case of power failure, watchdog loss (IP67 only)
  • IP67/IP54 housing; User friendly UI, including auto topology drawing; Complete CLI
  • N-key configurator** for upgrading, auto/editable configuration back up and restoration without computer

 

Lantech IPES-5416T-16 (IP67/IP54) is a high performance L2+ (Gigabit uplink) switch with 16 10/100TX (D-coded) + 4 10/100/1000T (X-coded) w/16 PoE 802.3af/at Injectors by M12 provides L2 wire speed and advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode, multiple VLAN mode with easy configuration. The comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+, SSH/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ are supported and also required in large network. It also supports Cisco Discovery Protocol (CDP) for Ciscoworks to detect the switch info and show on L2 map topology.

Up to 16 PoE ports with advanced PoE management
Lantech IPES-5416T-16 (IP67/IP54) supports IEEE802.3at/af standard which can feed HI-power up to 30W at each PoE port for big power consumption devices like PTZ IP camera, High power wireless AP etc. The advanced PoE management includes PoE detection and scheduling besides the regular PoE per port status. PoE detection can detect if the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Per port PoE status can remotely On/Off the power and display information of voltage, current, watt and PoE temperature.

Wide selection of input range models (24V/ WV) w/maximum PoE budget
The Lantech IPES-5416T-16 is designed with various dual power input to feed 54V PoE. The WV model accepts 16.8V~137.5V wide range input and yields PoE budget max 80W. Featured with relay contact alarm function, the IPES-5416T-16 (IP67/IP54) is able to connect with alarm system in case of power failure or port disconnection events. The 24V model accepts 12V~56V wide range input and yields PoE budget max.80W.

Miss-wiring avoidance, Repowered auto ring restore, Loop protection
The IPES-5416T-16 (IP67/IP54) also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IPES-5416T-16 (IP67/IP54) is able to alert with the LED indicator and disable ring automatically. Repowered auto ring restore function (node failure protection) ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.

DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server**
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch), it also can assign IP address by port for multiple switches with single DHCP option82 server. For the ending device which need to download file from TFTP server, DHCP Option66 server can offer IP address of TFTP server to DHCP client. Optional IPv6 address resolution for DHCP service can be supported.

Editable configuration file
Optional N key auto backup, exported text file

The configuration file of Lantech IPES-5416T-16 (IP67/IP54) can be exported and edited with word processor for the other switches configuration with ease. The built-in watchdog design can automatically reboot the switch when CPU is found dead. The optional N-key configurator offers firmware upgrade, auto/editable configuration back up and restoration without computer by adjusting the DIP switch.

User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes IPES-5416T-16 (IP67/IP54) much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.

Enhanced G.8032 ring, 16 MSTI MSTP; Optional MRP ring
Lantech IPES-5416T-16 (IP67/IP54) features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering multicast packets. It also supports various ring topologies that covers multi-chain (under enhanced ring), train ring, basic ring, multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows RSTP over VLAN for redundant links with 16 MSTI.

Optional MRP (Media Redundancy Protocol) can be supported for industrial automation networks.

QoS by VLAN for legacy device
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.

QinQ, QoS and GVRP supported
It supports the QinQ, QoS, GVRP for large VLAN segmentation.

IGMPv3, GMRP, router port, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port and static multicast forwarding binding by ports for video surveillance application.

Event log & message; 1 DI + 1DO
In case of event, the IPES-5416T-16 (IP67/IP54) is able to send an email** & SMS** text message to pre-defined addresses as well as SNMP Traps out immediately. It provides 1DI and 1DO when disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.

Environmental monitoring for switch inside information
The environmental monitoring can detect switch overall temperature, total PoE load, voltage and current where can send the SNMP traps, email** and SMS** alert when abnormal.

EN50155, EN45545-2, EN61373 verification; High ESD protection
Lantech IPES-5416T-16 (IP67/IP54) features high reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory and assembly lines.

The IPES-5416T-16 (IP67/IP54) is designed to meet with critical network environment with IP67/IP54 aluminum enclosure and M12 connectors for water proof. With EN45545-2 Fire & Smoke, and EN50155 & EN61373 verification, the IPES-5416T-16 (IP67/IP54) is the best for railway in train/track side, vehicle and mining applications. For more usage flexibilities, IPES-5416T-16 (IP67/IP54) supports wide operating temperature from -40°C to 75°C.

IPES-5416T-16 (IP67/IP54) also provides ±2000V EFT and ±6000V ESD contact protection, which can reduce unstable situation caused by power line and Ethernet

Optional smart bypass protection
The optional bypass relay is set to bypass the switch to the next one when power is off in order to protect the network from crashing. Lantech bypass caters to remain in bypass mode until the switch is completely booting up when power is back to avoid another network lost. The optional smart bypass can be activated when switch encounters power failure or watch dog hang. (IP67 only)

*Future release
**Optional