EN50155 Multifunction VPN Router up to 2 LTE 4G + 2 serial ports + 6 Gigabit X-coded Ethernet switch (incl. 4 PoE ports) w/ Load Balancing, VPN, Protocol Gateway, Storage**; WV input
- Built-in 4 Gigabit X-coded PoE Ethernet managed switch +2 WAN/LAN ports, Up to 2x LTE 4G Module ( 4SIMS)
- Support LTE Cat 6 (APAC & EUNA models) or Cat 12/9/13 (WW model)
- VPN router for Multi-site VPN, OpenVPN, L2TP over IPsec, IPsec, L2 over GRE , IPGRE
- Load Balancing built-in 5 mechanisms
- Optional EMMC Flash storage on-board**
- Support NAT and Firewall
- Support Modbus gateway on serial ports
- Support 2 RS422/RS485 ports with 2.5KV isolation or 2x RS232 ports
- Optional 2 GT smart bypass protection
- Galvanic isolation on WV model from 16.8V~137.5V input
- Environmental monitoring for router inside info with voltage, current, temperature and total PoE load; LTE graphic signal strength
- Editable login page of captive portal for hot-spot application
- USB port for backup, restore the configuration file and upgrade firmware; Dual image firmware
- IP 65 /54 Aluminum housing for best heat dissipation and preventing moist ingress
- EN50155/61373/45545verification for railway application
Lantech TPMR-5006 series is a next generation EN50155 multi-function VPN router up to 2 x LTE modem +6 Gigabit X-coded Ethernet switch incl. 4 PoE ports + 2 serial ports that supports advanced function of VPN, Load-balancing , EMMC Flash Storage**, Protocol gateway(Modbus), Storage**, and LTE dual SIM fail-over for industrial applications. The dual core CPU with 1.6GHz + 256M flash enables the router to multi-task smoothly.
Dual concurrent LTE design 4G/3G for load-balancing
With dual LTE module design (2L model), 4 SIM card slots, TPMR-5006 can allow auto-swap, failover & failback between multiple service providers for real non-stop connection. With concurrent LTE modules, it can also allocate bandwidth by “ Load Balancing with 8 schemes between multiple WANs. Both GPS and Russian GLONASS systems are supported.
Optional EMMC Flash storage**
The optional EMMC flash storage on router can offer 8G/16G/32G capacity.
Load Balancing with 5 mechanisms for multi-WANs
TPMR-5006 supports Load Balancing for LTE/WAN connections. There are five schemes for Load Balancing function:
|Basic||Fixed||Manually route by traffic type through fixed WAN link.|
|Failover||Routes connections through preferred WAN link while others stand-by. Sequentially activate another link if preferred link fail occurs. Once failover will not failback until link loss.|
|Priority||Routes connections through preferred WAN link as primary while others follow by. Ex. Wi-Fi client>LTE>others|
|Weighted Round-Robin||Evenly distribute the traffic over all working WAN links in circular order according to the specified weights.|
|Custom Route||Routing through the selected WAN for each specific traffic, ex: TCP/UDP port number and IP address.|
2 port serial connection, Modbus gateway
It builds in 2 port serial connection for RS232; RS422/ 485 in which RS422/RS485 has 2.5KV isolation protection. The built-in Modbus gateway can convert Modbus RTU/ASCII to Modbus TCP for device control.
VPN and firewall
Besides traditional VPN peer to peer tunneling, TPMR-5006 support latest Multi-Site VPN function that is an efficient way for mesh tunneling. The registration is under cloud service and encrypted by SSH makes the connection easy and safe. It supports Multi-Site VPN, OpenVPN, L2TP over IPsec, IPsec, L2 over GRE , IPGRE, and NAT for various VPN applications. The built-in Layer-4 firewall includes DDoS, IP address filter / Mac address filter / TCP/UDP port number.
Optional 2 GT smart bypass protection
The optional bypass relay is set to bypass the router to the next one when power is off in order to protect the network from crashing. Lantech bypass caters to remain in bypass mode until the router is completely booting up when power is back to avoid another network lost. Also it will be activated when detecting the router is hanged or link down.
DIDO for alarm & email notice; Event log; Remote Web control
2 sets of DIDO function can support additional high/low physical contact for designate applications besides Port / Power events, for example, DIDO function can trigger alarm if the router was moved or stolen. In case of events, the TPMR-5006 will immediately send email and trap. The event log can be sent via syslog, emails or trigger the alarm relay. When the router is at remote area with limited access, Web control can help to get router status or remotely reboot by Web.
Wide range dual input voltage from dual input voltage from 16.8-137.5V (WV model)
The TPMR-5006 is able to work from dual 16.8V ~137.5V DC isolated input (WV model) for PoE at/af with PoE budget 60W that is particular good for vehicle, rail train, depot etc applications.
Built-in Managed Switch Function
Managed switch function is built-in and provides various L2+ functions for network access deployment. It delivers ports and PoE management, VLAN, QoS, multicast, redundant ring, and security functions.
Environmental monitoring for inside router info& alerting; LTE signal strength
The built-in environmental monitoring can detect router ambient temperature, voltage, current and total PoE load where can send the syslog and email when abnormal. The LTE signal strength shows connection status at a glance.
Editable login page of captive portal
The TPMR-5006 supports editable captive portal function that allows administrator to force end-users redirect to authentication page.
USB port for back up, restore configuration and upgrade firmware Dual image firmware
The built-in USB port can upload/download/upgrade the configurations through USB dongle for router replacement It supports dual-image firmware to choose which one to start
Ruggedized EN50155 design and FCC/CE & E-marking** certificate
The TPMR-5006 series is verified with EN50155, EN61373, EN45545 standard with IP65/54 housing. It passed tests under extensive Industrial EMI and environmental vibration and shocks standards. With CE & FCC radio certification for LTE and E-marking** certificate, the TPMR-5006 is best for outdoor community, vehicle, power substation, process control automation etc application. For more usage flexibilities, TPMR-5006 supports operating temperature from -40°C to 65°C.